GCSE Physics required practical questions test more than whether you remember an experiment. You may need to identify variables, select equipment, complete a results table, interpret a graph, calculate a value and evaluate the method. This reusable checklist covers the practical skills behind common GCSE Physics experiments, while reminding you to check the exact required-practical wording for your exam board and specification.
Overview
Required practicals are assessed through written questions as well as classroom work. A question might show an unfamiliar apparatus diagram or data set, but the marks usually reward familiar scientific decisions: changing one variable, measuring another, controlling other conditions and explaining how to improve reliability.
AQA, Edexcel and OCR specifications do not always use identical practical lists, equipment or wording. Use this article as a GCSE Physics revision framework, then compare it with your own specification, teacher’s practical booklet and official exam-board guidance. The essential preparation is to understand the purpose of each investigation rather than memorising a script.
The practical-question checklist
- Aim: What relationship or quantity is being investigated?
- Independent variable: What will be deliberately changed?
- Dependent variable: What will be measured or observed?
- Control variables: What must remain constant for a fair test?
- Equipment: Can you name suitable measuring instruments and their units?
- Method: Are the steps ordered, repeatable and sufficiently precise?
- Safety: What hazard is present, and what control reduces the risk?
- Data: Are headings, units, decimal places and significant figures consistent?
- Analysis: Is a graph, gradient, mean or equation required?
- Evaluation: Can you identify a specific limitation and a realistic improvement?
Checklist by scenario
1. Measuring density
For a regular solid, measure its mass with a balance and its dimensions with a ruler or vernier calliper. Calculate volume from the dimensions, then use density = mass ÷ volume. For an irregular object, measure mass and find volume by water displacement in a measuring cylinder. Read the bottom of the meniscus at eye level and ensure the object is fully submerged without trapping air.
The independent variable may be the object or material being tested; the dependent variable may be mass, volume or calculated density, depending on the question. Control the measurement technique and use the same units throughout. A results table could include object, mass in grams, initial volume in cm³, final volume in cm³, displaced volume and density in g/cm³.
Safety and evaluation: Handle glassware carefully and dry the object before measuring its mass. Improve reliability by repeating readings and using a larger object where suitable, because a small reading error can have a larger effect on the calculated density.
2. Specific heat capacity
Measure the mass of a metal block, attach an electrical heater and thermometer, then record the starting temperature. Switch on the heater for a measured time and record the final temperature. Energy transferred can be found from the heater’s power and time, and specific heat capacity can be calculated using energy transferred = mass × specific heat capacity × temperature change.
Typically, time or electrical energy is changed and temperature change is measured. Keep the block’s mass and material constant. Record power, time, starting temperature, final temperature and temperature change. Insulate the block and improve thermal contact between the heater and block to reduce energy lost to the surroundings.
Safety: The heater, wires and block may become hot. Use heat-resistant handling procedures, keep liquids away from electrical equipment and switch off the supply before moving apparatus.
3. Resistance and current–voltage characteristics
Build a circuit with a power supply, ammeter, voltmeter and the component being investigated. An ammeter is connected in series; a voltmeter is connected in parallel across the component. Vary the potential difference and record current and voltage. Calculate resistance using resistance = potential difference ÷ current when appropriate.
For a fixed resistor, the relationship may be approximately proportional over a suitable range. For a filament lamp or diode, the relationship is not necessarily proportional. The component is the independent focus, while voltage and current are measured variables; the current or potential difference is changed using the power supply or a variable resistor. Use a results table with voltage in volts, current in amperes and resistance in ohms if resistance is requested.
Safety and evaluation: Keep the current low enough to prevent overheating, and open the switch between readings where appropriate. A lamp’s temperature changes as it operates, so allow for this when explaining a curved graph. Take several readings across the range and plot a correctly labelled graph with sensible scales.
4. Force, extension and elastic behaviour
Attach a spring to a clamp stand, measure its original length, then add loads one at a time. Record the new length and calculate extension by subtracting the original length. Do not confuse extension with total length. Plot force against extension if asked, using the weight of the load as force where suitable.
The load or force is changed and extension is measured. Keep the same spring, ruler position and measurement method. Read the ruler at eye level and allow the spring to stop moving before recording a value.
Safety and evaluation: Prevent falling masses from striking feet and do not add loads that permanently deform or break the spring. Repeat readings, use a pointer or marker to improve scale readings and identify the limit of proportionality from the graph rather than assuming it is the final point.
5. Waves and measuring wave speed
For waves on a ripple tank, rope or other medium, measure wavelength and frequency, then use wave speed = frequency × wavelength. Measure the distance across several wavelengths and divide by the number of wavelengths to obtain a more reliable average. For a ripple tank, keep the water depth and wave source conditions consistent.
For sound, a signal generator and oscilloscope or microphone may be used, depending on the equipment available. Identify whether frequency, wavelength, distance or time is being measured, and include units in every table heading.
Safety and evaluation: Keep electrical equipment away from water and reduce parallax by viewing scales straight on. Repeating measurements and measuring several wavelengths usually reduces the effect of a single reading error.
6. Acceleration and motion
In a trolley investigation, measure time over a known distance using light gates, a motion sensor or another suitable timing method. Change the force or mass according to the investigation and keep other relevant quantities controlled. Record distance, time, velocity or acceleration as requested, and check whether the method measures an average or instantaneous value.
Use a level track where appropriate, secure the pulley and ensure the trolley cannot roll unpredictably. Repeat each measurement and calculate a mean, but investigate an anomalous value rather than deleting it without explanation.
7. Radiation investigations
When investigating background radiation or the effect of distance and shielding, take a background count for a fixed time before measuring the source. Repeat counts because radioactive emissions are random. Subtract background count when the question or method requires a corrected count.
Change one factor, such as absorber material or distance, and keep counting time and detector position consistent. Follow teacher instructions for handling sources, minimise exposure time, maximise distance where possible and use shielding as directed. Do not describe a result as proving that radiation is safe simply because one reading is low.
What to double-check
Variables and fair testing
Write variables precisely. “Temperature” is incomplete if the investigation needs the temperature of a particular block. “Amount of wire” is less useful than “length of wire”. A control variable should explain what stays the same and why it matters, such as the wire material, cross-sectional area or temperature.
Results tables
Put the quantity and unit in the heading, for example length / cm or current / A. Do not place units in every cell. Use a consistent number of decimal places where the measuring instrument supports them. Include repeats, means and calculated columns when they are relevant. Leave enough space for the full range of results rather than rounding readings too early.
Graphs
- Put the independent variable on the horizontal axis and the dependent variable on the vertical axis.
- Label both axes with quantities and units.
- Use most of the grid and choose an even scale.
- Plot points accurately with a small cross or fine dot.
- Draw a line or curve of best fit rather than joining every point dot-to-dot.
- Only force a line through the origin if the physics and data justify it.
- For a gradient, use a large triangle on the best-fit line, not two nearby data points.
For more support with practical data, uncertainty and significant figures, see this guide to uncertainty, errors and significant figures; the calculation principles are useful practice even though the linked article is aimed at A-level.
Evaluation language
A strong evaluation connects a limitation to its effect. Instead of writing “use better equipment”, write “the ruler reading is limited by the millimetre scale, so use a vernier calliper to reduce uncertainty in the diameter measurement”. Useful improvement prompts include insulation, a light gate instead of a handheld stopwatch, measuring several intervals, repeating readings, controlling temperature and using a wider range of values.
Common mistakes
| Common error | Better answer or improvement | Likely credit |
|---|---|---|
| Calling every variable a control variable | Name the variable that is changed, the variable measured and the conditions kept constant. | Correct identification of variables and fair-test reasoning. |
| Using “repeat it” without a purpose | Repeat readings, calculate a mean and identify random variation or an anomalous result. | Reliability and data-processing credit. |
| Writing “take more care” | Give a specific change, such as reading the meniscus at eye level or using a light gate. | Actionable improvement linked to a limitation. |
| Joining graph points with straight lines | Use a best-fit line or curve, unless the question specifically asks for point-to-point joins. | Graph construction and relationship credit. |
| Ignoring zero error or background radiation | Check the instrument reading before the experiment or measure and account for background count. | Accuracy and correction credit where relevant. |
| Giving a hazard without a control | State both the hazard and the action that reduces its risk. | Safety-method credit. |
| Confusing precision with accuracy | Explain whether repeated readings are close together or close to the accepted value. | Evaluation of measurement quality. |
Before a past-paper session, choose one practical and write its aim, variables, method, safety point, table headings, graph plan and two evaluation points from memory. Then compare your response with the mark scheme. For a broader revision plan, use the GCSE Combined Science Physics revision checklist if you are studying the combined course, and practise explaining method choices in the same way as a six-mark response using this six-mark question guide.
When to revisit
Return to this checklist at four useful points:
- Before the classroom practical: confirm the aim, equipment, variables and safety controls.
- After the practical: rewrite the method from memory and annotate your own results table and graph.
- Before a past-paper session: practise one unfamiliar data set, especially evaluation and graph questions.
- Before exams or after specification updates: compare your practical list, required equipment and wording with the current guidance for AQA, Edexcel or OCR.
Keep a short practical-mistake checklist in your GCSE Physics revision notes. Add errors such as missing units, incorrect axis choice, weak improvement statements or confused series and parallel circuit connections. Revisiting those specific mistakes is more effective than rereading every method. Required-practical questions become manageable when you treat them as a repeatable process: identify the variables, measure carefully, present data clearly, use the physics and evaluate the evidence.